City Affairs|150 degrees Celsius! "The hot spot is okay, the quality of the work under our hands must be higher than the temperature."

On July 3, 2025, it was located in the outdoor yard of Jiangnan Shipbuilding and Manufacturing Department No. 2. At this time, the temperature of the steel plate at Wang Xiaojun's feet suddenly soared to 156.6 degrees, because this kind of heat can make people jump from the heat through labor protection shoes.
156 degree steel plate side welding 35mm hull
For those thick plates with a thickness of more than 35 mm, they must be preheated to almost 150 degrees before formal welding operations. This regulation is considered a rigid indicator in the industry.
Because according to Qin Xiangman from the quality team, as the thickness of the steel plate continues to increase, the thermal stress and shrinkage during cooling will become more and more obvious. If these thick steel plates are not preheated, the final welded product will almost certainly have pores and cracks.
The outdoor temperature that day was close to 40 degrees, and the surface of the steel plate added heat to 150 degrees. When I used a thermometer gun to illuminate the position next to my feet, it directly showed a value of 156.6 degrees. The soles of the labor protection shoes gave people the feeling of stepping on a red-hot iron plate. There was no difference.
The preheating temperature is stuck at 100 to 200 degrees
The preheating range of different steel materials is usually in the range between 100 degrees Celsius and 200 degrees Celsius. If the temperature is too low, it will not be able to reduce thermal stress, and if the temperature is too high, it will cause damage to the performance of the steel, so it must be carefully controlled according to the specific material.
The staff is always looking at the thermometer gun and using it to record data. Only when the temperature of each plate is at the right point is the welder allowed to put down the welding gun and officially start welding. If the data differ by only a few degrees, it must be readjusted without any ambiguity.
Automatic welding machines are also inseparable from human supervision

Although the welding machine is automatic, the welding effect must be uniform. Once any remaining welding slag is found, it must be cleaned up immediately. Master Wang is operating through a welding mask, and the high temperature bakes his face red and bright.
He said that the sweat on his face has completely evaporated, so it cannot flow down his cheeks. However, occasionally a sweat drop will fall from his eyelids and fall directly into his eyes. At this time, he only needs to blink twice and the specific direction of the weld is completely unclear, and he can only rely 100% on the feel to complete the operation.
Hot hands are a common occurrence
The temperature of all the surrounding metal facilities is over 100 degrees. Although the machine has stopped running, the average temperature of the steel plates is still above 140 degrees. If you touch it with your hands, blisters will form immediately. On the cloth used to prevent burns, small slag splashed during welding penetrated into it, forming dense holes.
Before starting work, people must put on hoods, gloves and masks. The situation of skin being burned by arc light is actually more frightening and dangerous than the damage caused by high temperature. Get yourself fully equipped. Pre-welding preheating and post-welding insulation for hull riveting welding are the bottom line that must be adhered to, rather than an option that can be chosen or not. If you are missing one piece of protective equipment, it is not allowed under any circumstances.
Take a break in between

With the advent of hot weather, the work rules on site have been modified to take breaks between work in the morning and evening to avoid the hottest two or three hours at noon. During the break, the workers took off their hoods and the clothes inside were soaked and they could squeeze out half a cup of water.
In each work area, a rest area has been set up specifically to escape the heat. On the tables in these rest areas, there are barley tea and iced salt soda. The workers took the opportunity to rest and take a breath before going to work. The rhythm of the entire work cannot be relaxed at all and must remain the same.
Mass is higher than temperature
Although the Internet is very lively now, the quality of the work we do is definitely higher in standard than those that are popular on the Internet. This sentence is really not just said casually. For example, the 35 mm thick steel plate must pass the non-destructive inspection after welding. Even if there is a defective solder joint, there is absolutely no way to avoid the inspection results.
Things start with the preheating step, then proceed to the pre-welding preheating and post-welding insulation of the hull riveting operation, and finally the post-welding insulation treatment. In each of these steps, there are dedicated staff who monitor the pre-welding preheating and post-welding insulation of the hull riveting on-site, and are responsible for recording relevant data. This requirement is a rigid rule passed down from one generation to another by dozens of generations of welders in the Jiangnan Shipbuilding Department.
When the temperature reaches 156 degrees, can you still stay at your feet and work? Among all the improvement projects, which one do you think should be given the highest priority? You can chat about your thoughts in the comment area. If you think this point of view is very practical, then please like it and forward it to those who are in the same industry as you to take a look.












No comments yet