Can 304 Stainless Steel Magnets Be Attracted?

Can 304 stainless steel magnets be attracted?

When many factories produce 304 stainless steel parts, after the parts are processed, they use magnets to close the stainless steel parts to remove the magnetism . They find that the magnets can actually attract them. When the customers inspect the goods, they return the goods directly to the manufacturer. The problem that led to this situation is mainly due to the failure to do a good job in the process of removing magnetism. Today I will explain the whole situation clearly to you.

Is 304 stainless steel itself magnetic?

304 is an austenitic stainless steel.铬含量为百分之十八, 镍含量为百分之八。 The crystal structure is face-centered cubic at room temperature. The magnetic moments cancel each other out and there is basically no magnetism. Take a brand new plate as a touchstone for stainless steel processing and magnetic removal , and use a magnet to attract stainless steel processing and magnetic removal. Can 304 stainless steel be attracted by a magnet? , the result is unstoppable.

However, it can be seen in the market that some items are marked with 304 material, but the raw materials inside are actually produced by fake 201 or 430. If the proportion of ferrite or martensite increases, the magnet will be able to absorb it directly. You must first confirm what the specific material is, and then discuss the topic of magnetism. If you do not do this, your work will be in vain.

Why does processing introduce magnetism?

Cold working methods such as lathe cutting, punching, and bending will deform the crystal structure in the part, and martensitic transformation will occur in local areas. As a result, the remaining magnetic field strength suddenly jumps from the previous low level of tens of amperes per meter to the high level of thousands of amperes per meter. This is the basic principle used to introduce magnetism through processing methods.

304不锈钢非磁性_不锈钢加工磁性去除_304不锈钢奥氏体结构

There is a hardware factory in Shanghai that reported in 2024 that a batch of stamped 304 gaskets had a residual magnetism of up to 1200A/m. Because the customer made medical devices, they directly determined that this batch of products was unqualified, causing the entire batch of goods to be scrapped, causing a loss of hundreds of thousands of yuan.

去磁的常见方法

The most commonly used equipment is the power frequency demagnetizer. The principle of this method is to place the workpieces in an alternating magnetic field, and then slowly and uniformly move them out of the range of the magnetic field. In this way, the residual magnetism indicator can be reduced to a value range below 50A/m. For example, several electronic factories in Shenzhen will run this set of processes every week. The result is that they spend money on equipment. Usually, the cost can be fully recovered within a short period of two or three years.

如果是小批量处理, 可以用手动退磁棒。 During operation, stroke in an S-shaped path along the surface of the workpiece. After you finish stroking, slowly pull it apart. This method is not efficient.但是它非常灵活。 So it is suitable for dealing with sporadic repair parts. But it is not suitable for batch operation scenarios on production lines.

去不干净的几个坑

In order to save trouble, many workshops do not adjust the current parameters of the demagnetizer in place, or do not move the workpieces out of the center area of ​​the magnetic field in a uniform and smooth manner, but directly throw them to the side. As a result, the residual magnetism cannot be effectively reduced at all. This situation is equivalent to not achieving the desired effect at all.

There is also a situation where multiple workpieces are stacked and demagnetized together. This operation method will cause the outer objects to appear to have been relatively clean, but the inner objects still retain the magnetism. A processing factory in Guangzhou had such a quality accident in 2025. As a result, customers complained about the incident and the company was required to pay compensation of 80,000 yuan.

怎么验收才靠谱

304不锈钢非磁性_不锈钢加工磁性去除_304不锈钢奥氏体结构

You cannot just rely on magnets to conduct testing, because using magnets can only tell you whether the item is magnetic, but it cannot tell you what the specific value of the residual magnetism is. Therefore, you must rely on two devices, the Gaussmeter or the residual magnetism detector, and you also need to read the relevant data one by one in strict accordance with the indicators clearly specified on the drawings provided by the customer.

For medical devices and electronic components, the usual requirement is that the residual magnetic induction intensity should not exceed 5 amps per meter. In more stringent cases, the requirement may not exceed 1 amp per meter. The standards for ordinary hardware are relatively loose. However, in the contract, the exact value must be written clearly, and it must not be vague.

Do not reverse the order of processing and demagnetization

The correct process is that all cold working processes must be completed first, and then demagnetization should be done as the last step. After completing the demagnetization step, you must never come into contact with any iron tools and fixtures. If you encounter these magnetic things after demagnetization, all the previous efforts will be in vain, because the magnetism of the material will be introduced into the workpiece again.

When a factory in Hangzhou first started working in 2026, the task of removing magnetism was placed at the forefront of the welding process. After everyone completed the welds, the material was stained with the magnetic influence of magnet adsorption, so they had to rework three times before finally meeting the standard requirements. This was a complete waste of two days of production capacity, and in the end, the person in charge was directly deducted points from the performance appraisal.

After all the 304 products produced in your factory are processed, the value of residual magnetism is usually limited to the range of A/m? Everyone is welcome to share the specific content of the magnetic field removal plan you have adopted in the comment area; if you think the discussion content is of practical value; then please perform like actions, collection operations and forwarding actions; forward this content to colleagues working in the workshop for a look.

© Copyright Notice
THE END
喜欢就支持一下吧
Likes14 Share
评论 Be the First to Comment

Please log in to comment

    No comments yet