How To Clean And Maintain Stainless Steel And Pay Attention To Daily Use

How to clean and maintain stainless steel and pay attention to daily use

After the stainless steel is processed, its surface will be covered with oil stains, rust spots and scale, which cannot be cleaned no matter how hard it is cleaned. This actually means that the method is not done correctly. The methods introduced below can all be applied.

How to remove surface dust and film residue

After processing, dust and adhesive film will stick to the surface. In this case, a neutral detergent in warm water will suffice. Wet the cotton cloth and twist it until it is semi-dry, then wipe it along the texture of the panel. If you find that the film has warped edges, you can use alcohol cotton to apply it on the inside for a while, wait until it softens, and then tear it off. Do not pull hard, otherwise it will leave offset marks.

Take out the remaining adhesive on the label, dip a piece of cotton cloth in alcohol or acetone, and gently wipe the area. It will be removed in about ten seconds. After wiping it, use a dry cloth to dry it immediately. Otherwise, when the water stain dries, white marks will be left again. In this case, you will have to clean it again in the next round.

How to remove oil stains and lubricants

To clean up the oil slick, the first step is to wipe the surface with a dry soft cloth, then take out the rag soaked in neutral laundry detergent or ammonia water, carefully wipe it two times along the texture, then briefly rinse it with water, and finally dry it with a dry cloth. How to clean stainless steel after processing . The entire process from start to finish should not take more than 5 minutes.

Do not use gasoline or banana water, because these organic solvents will destroy the oxidation protective layer on the surface of stainless steel. Over time, spots will appear on the surface that cannot be washed away. If you encounter oil stains that cannot be wiped off, use a special stainless steel cleaning paste and gently rub it back and forth along the texture of the stainless steel. After grinding, be sure to rinse it with water immediately.

Emergency treatment after acid adhesion

Once it is stained with dilute hydrochloric acid or nitric acid, you will have a reaction in your heart. Find a place with clean water to rinse immediately, and rinse it for at least thirty seconds, so that all the acid can be washed away. During this process, you also need to wear rubber gloves to protect your skin, because the longer the acid stays on the skin, the more serious the damage it will cause to the skin, so you must not touch it directly with your hands.

After rinsing, soak and clean with 10% ammonia or baking soda water for two minutes, then rinse with warm water, and then wipe your hands dry. If you find white spots on the surface, use fine abrasive paste to gently polish along the direction of the grain. After polishing, rinse the surface immediately. Do not delay, otherwise the white spots will spread over time.

Rainbow pattern and rust spot treatment

If rainbow-colored stripes appear on the surface, most of the reasons are that too much cleaning fluid has been put in, or that the previous layer of oil stains has not been completely removed.

You can first use slightly hot water mixed with a mild detergent and scrub it repeatedly for about three or four times, so that the marks will disappear naturally. Be careful not to use cleaning products with too high alkali content, otherwise it will make the surface look more mottled and very ugly.

Apply 10% nitric acid to those areas where rust is really occurring, or use a special abrasive paste to gently polish along the grain direction. When the rust is completely gone, rinse and dry it immediately. If the rust spots are not treated immediately, they will spread along the direction of the grain boundaries, causing the area covered by them to become wider and wider.

Maintenance details of different panels

After tearing off the protective film on the wool surface, use a vegetable cloth dipped in detergent water and wipe it along the lines without making circular motions. Finally, use a dry cloth to drain the moisture. For the shiny part of the mirror, just wipe it gently with a fine towel dipped in water. If you encounter rough items, be sure to avoid them, because once scratches occur, they are permanent.

After wiping it clean, be sure to use a dry cloth to dry up the moisture on the surface. Otherwise, if the water stains are allowed to dry naturally, white marks will be left, which will make it very difficult to clean again. If the cover will not be used for half a year, it should be placed in a plastic bag to isolate the air, and then stored in a ventilated and dry place to reduce the probability of oxidation spots.

Don’t step into pitfalls when using stainless steel tableware in daily use

Don't use those bowls and pots to hold things like soy sauce, salt or pickle soup for a long time. Because the electrolyte here will react with the metal and then dissolve some trace elements. So throw things away after use and rinse them thoroughly. There are also methods for cleaning stainless steel after processing , and do not fry Chinese medicine in it. Organic acids and high temperatures will cause the medicinal effect to be lost, and a lot of impurities will be added.

Never use bleach or soda water when washing dishes, because those substances that are strong alkalis and strong oxidants will make the surface dark and gray. It is enough to add detergent to warm water. Dry them and store them upside down. How to clean and maintain stainless steel? Pay attention to daily use, so that there will be no accumulation of water or mildew, and it will look like new after two or three years of use.

What type of stains are most troublesome to you on the stainless steel pots and pans in your home? Please talk about the specific content in the comment area, so that when you like and save it, it will be very convenient to find it next time and follow the method to perform cleaning actions.